This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
manual:user_guide:tracks:editing [2017/10/26 10:56] – [Track repairs] mstupka | manual:user_guide:tracks:editing [2020/09/02 19:14] (current) – [Shortening] mstupka | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Track/Route Editing ====== | ====== Track/Route Editing ====== | ||
- | FIXME IN RECONSTRUCTION FIXME | ||
---- | ---- | ||
===== Route re-planning ===== | ===== Route re-planning ===== | ||
Line 11: | Line 10: | ||
* from the **route detail menu**:\\ {{ : | * from the **route detail menu**:\\ {{ : | ||
==== Changing progress ==== | ==== Changing progress ==== | ||
- | Drag shaping {{: | + | Drag shaping {{: |
+ | ==== Editing navigation commands ==== | ||
+ | **Navigation hints** are added to Locus routes **automatically** (it can be switched off, see [[manual: | ||
+ | |||
+ | Sometimes you may want to correct these hints: | ||
+ | === Removing === | ||
+ | * open route in **Route planner** and **tap the navigation point**:\\ {{ : | ||
+ | * select {{: | ||
+ | |||
+ | === Changing === | ||
+ | * **tap the navigation point** in the route planner | ||
+ | * tap the navigation point button | ||
+ | * select the navigation command:\\ {{ : | ||
+ | |||
+ | === Adding === | ||
+ | * open route in **Route planner** and tap the place where you want to add navigation point | ||
+ | * open the trackpoint menu and tap the navigation button | ||
+ | * select navigation command:\\ {{ : | ||
+ | |||
==== Extending ==== | ==== Extending ==== | ||
Add {{: | Add {{: | ||
Line 17: | Line 34: | ||
Remove {{: | Remove {{: | ||
- | <wrap info> | + | <WRAP info round> |
+ | * When you need to edit an imported route, it is necessary to add shaping points to it first | ||
+ | * More details about route planning in [[manual: | ||
+ | </WRAP> | ||
==== Saving changes ==== | ==== Saving changes ==== | ||
Open the topbar {{: | Open the topbar {{: | ||
Line 49: | Line 69: | ||
Sometimes it happens you forget to stop track recording when arriving from your trip to the train station and the recording goes on in the train. You need to remove the train part: | Sometimes it happens you forget to stop track recording when arriving from your trip to the train station and the recording goes on in the train. You need to remove the train part: | ||
* tap the place of your track where you arrived at the train station:\\ {{ : | * tap the place of your track where you arrived at the train station:\\ {{ : | ||
- | * select **Delete all after** from the tool mnenu:\\ {{ : | + | * select |
* **confirm deleting** of the remaining part of the track:\\ {{ : | * **confirm deleting** of the remaining part of the track:\\ {{ : | ||
==== Inserting a gap ==== | ==== Inserting a gap ==== | ||
+ | Imagine you record your running workout and for some reason you have to use the street bus in the middle of it. You actually forget to pause the recording. Afterwards, you need to erase the bus part from your track and leave the space empty. | ||
+ | * tap the point on your track where you got on the bus:\\ {{ : | ||
+ | * select {{: | ||
+ | * a gap appears between selected trackpoint and the next trackpoint: | ||
+ | * repeat the step above until you get to the point you got off the bus and went on running:\\ {{ : | ||
- | ---- | + | <WRAP center round tip> |
- | OBSOLETE: | + | This step can be reversed by tapping |
- | If you want to edit saved tracks (e.g. due to inaccuracy of the GPS recording) or already planned route, you can do so directly on map: | + | |
- | * **select a track/route to edit** - in the data manager or on the map\\ \\ | + | |
- | * select | + | |
- | * a **new bottom panel** emerges: | + | |
- | * {{: | + | |
- | * {{: | + | |
- | * {{: | + | |
- | * //Display on chart// - displays selected trackpoint on chart | + | |
- | * // | + | |
- | * //Convert to navigation waypoint// - offers selection of navigation commands to associate to the point and converts it into a navigation waypoint\\ \\ <WRAP center round tip> | + | |
- | TIP: when two coincident trackpoints covering each other occur and you want to add navigation command to the other that is not displayed, tap the point twice to switch between them. | + | |
</ | </ | ||
- | * //Delete trackpoint// | + | ==== Splitting track ==== |
- | * //Cut part of track// - selects a part of track to cut out (useful | + | You can split track in two or more parts e.g. when you have multiple day track recording: |
- | * //Remove all before// - deletes all trackpoints from the start of the track to the selected trackpoint | + | * tap the point on the track where you want to split it:\\ {{ : |
- | * //Remove all after// - deletes all trackpoints | + | * select {{: |
- | * //Split// | + | * confirm if you want to keep the original |
- | * {{: | + | * two new tracks are created in the same folder:\\ {{ : |
- | * {{: | + | |
- | * {{: | + | ==== Inserting/editing trackpoints ==== |
+ | Trackpoints are **basic particles** tracks are made of (resp. routepoints are particles of routes). Track/route editor enables also edits on this miniature level - e.g. when **automatic route drawing makes mistakes**: | ||
+ | * tap the track and select **Insert/ | ||
+ | * trackpoints are highlighted | ||
+ | * **change course** | ||
+ | * if you want to undo, tap {{: | ||
+ | * route is repaired:\\ {{ : | ||
+ | ==== Deleting trackpoints ==== | ||
+ | Sometimes it happens that Locus receives **wrong coordinates** of one trackpoint from GPS during recording which results in a " | ||
+ | * tap the wrong part of the track:\\ {{ : | ||
+ | * select **Delete trackpoint**: | ||
+ | * **confirm** action:\\ {{ : | ||
+ | * repaired track:\\ {{ : | ||
+ |