User Tools

Site Tools



This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
manual:user_guide:tools:altitude [2015/03/31 09:29]
mstupka created
manual:user_guide:tools:altitude [2016/10/21 16:39] (current)
Line 1: Line 1:
-====== Altitude Manager ======+{{ :manual:user_guide:ic_altitude_manager_alt.png?nolink|}}====== Altitude Manager ======
 ---- ----
-<todo>later...</todo> +===== About ===== 
-....................................... +<wrap box>Menu > Settings > GPS and location > Altitude manager</wrap>
-Altitude offset +
-Use altitude offset +
-Define offset between real and GPS altitude+
-Pressure sensor +Altitude manager enables to fine-tune obtaining altitude values from your mobile device. It is divided into three main tabs: 
-Use pressure sensor +  * **main settings** 
-Measure precise altitude by pressure sensor +  * **settings of altitude offset** 
- .... +  * **settings of pressure sensor** 
-Altitude filter +===== Settings ===== 
-Apply filter to altitude. Heavier filters cause less fuzzy altitude values but slower reaction on altitude changes.+Contains general switches of offset and pressure sensor and settings of SRTM data assistance and altitude measurement filter:\\ {{ :manual:user_guide:tools:altmanager.png }} 
 +====  SRTM data ==== 
 +{{ :manual:user_guide:tools:altmanager4.png?nolink |}} 
 +  * **No usage** - altitude values are acquired from GPS only 
 +  * **Optimize GPS altitude** - uses [[|offline elevation data (SRTM)]] to optimize GPS altitude values. Computed altitude has similar accuracy to an average GPS but does not contain serious errors GPS units usually make. SRTM data can be downloaded [[manual:faq:how_to_add_map_shading|several ways]]. 
 +  * **Replace GPS values** - uses [[|offline elevation data (SRTM)]] only for displaying elevation 
 +<WRAP round alert > 
 +**Warning for pilots**: optimizing or replacing GPS altitude by SRTM data is not recommended for activities when you are **not moving on the ground** - displayed altitude values are influenced by the ground altitude measuring and calculation 
 +==== Altitude filter ====
-Offset +Applies filter to altitude measurement to reduce value fuzzinessHeavier filters cause less fuzzy altitude values but slower reaction on altitude changesScale ranges from no filtration to an ultra heavy filter. 
-........... +===== Altitude offset ===== 
-Enable Altitude offset in settings tab before setting offset parameters. +{{ :manual:user_guide:tools:altmanager2.png }} 
-...+Altitude calculated by internal or external (Bluetooth) GPS unit is related to a different method of referencing the Earth surface than that used in maps. The difference between them is called **Geoid height** which is distance between [[|Geoid]] and [[|reference elipsoid]].
-Pressure +Locus Map can define this offset by three methods: 
-............. +  * **Manual correction** - basic method used when the exact offset value is known 
-Enable Pressure sensor in settings tab before setting pressure parameters.+  * **Automatic correction** - method used in most cases - Locus Map can compute offset of the whole world from a Geoid modelThis method is accurate enough for use in mobile phones and sufficiently precise for all locations (the offset slightly varies based on location)<wrap info>This method is available in Locus Map Pro only</wrap> 
 +  * **Altitude NMEA correction** - mobile device communicates with GPS unit over a special messages called NMEAThese messages contain values of Geoid height that Locus Map can read and apply them to correct this offset.<wrap alert>Some devices report incorrect values so this method is unreliable.</wrap> 
 +  * **Enable also for Bluetooth GPS** - check this option if you use external GPS device 
 +===== Pressure sensor ===== 
 +{{ :manual:user_guide:tools:altmanager3.png }} 
 +Some devices are equipped with barometric pressure sensorBarometric sensors measure atmospheric pressure very precisely which can be used for calculating relative altitude changesI.eif you know certain pressure at certain altitude you can calculate altitude changes between known and current position. 
 +The pressure sensor must be calibrated to a known altitude value so that it can be used for real altitude value calculationsLocus Map offers several methods: 
 +  * **Automatic** - Locus Map uses GPS altitude or SRTM files altitude and current barometric pressure as basic values and relates all other measurements to these valuesIt also checks measured values in 2 hour intervals and eventually re-calibrates the pressure sensor.<wrap info>This method is available in Locus Map Pro only.</wrap> 
 +  * **Pressure at sea level** - current pressure value at a particular sea level as the reference can be obtained from the Internet. The resulting altitude calculation is also quite accurate but the base pressure changes in time so it can be a problem. 
 +  * **Altitude** - uses some other source of ground altitude - external maps, measuring, tourist guide posts, etc. as the reference. Locus Map then calibrates the pressure sensor according to this value. 
 +<WRAP  round important>Some devices like e.g. Samsung Galaxy Note II turn off the pressure sensor in standby mode. If you want to use pressure sensor during e.g. track recording, make sure your device maintains the pressure sensor on also when the screen goes off. 
-Automatic calibration according to GPS 
manual/user_guide/tools/altitude.1427786955.txt.gz · Last modified: 2015/03/31 09:29 by mstupka